Omni Calculator logo

Stress Calculator

Created by Bogna Szyk
Reviewed by Steven Wooding
Last updated: Jan 16, 2024


This stress calculator will help you solve the problems in mechanics involving stress, strain, and Young's modulus. In a few simple steps, you will learn the stress vs. strain relationship for any material that remains elastic. We will also teach you how to calculate strain and how to apply the stress equation.

🔎 This calculator deals with axial stress. If you're studying transverse shear, you should look at our shear stress calculator.

How to calculate strain and stress

Strain is defined as the measure of deformation – a proportion between the change of length and the original length of an object. For example, if you take an elastic band and stretch it so that it is twice longer than initially, then the strain will be equal to 1 (100%).

The formula for strain is:

ε=ΔLL1=L2L1L1\varepsilon = \frac{\Delta L}{L_1} = \frac{L_2 - L_1}{L_1}

L₁ denotes the initial length, L₂ – the final length, and ΔL is the change in length. Note that strain is dimensionless.

Stress, on the other hand, is the measure of pressure that the particles of a material exert on each other. It is defined as the force acting on the object per unit area. It is different from the pressure, though; when calculating stress, the area considered must be so small that the analyzed particles are assumed to be homogeneous. If we take into account a bigger area, the calculated stress is usually the average value.

The stress equation is:

σ=FA\sigma = \frac{F}{A}

F denotes the force acting on a body, and A denotes the area. Units of stress are the same as units of pressure – Pascals (symbol: Pa) or Newtons per squared meter.

Positive stress means that the object is in tension – it "wants" to elongate (elongation Calculator). Negative stress means that it is in compression and "wants" to become shorter.

Do you know?
There are two types of strain — engineering and true strain. Find out more in our true strain calculator

Young's modulus (stress vs strain)

If the material is linearly elastic, then the stress and strain are directly related with the following formula:

E=σεE = \frac{\sigma}{\varepsilon}

E is the modulus of elasticity, or the Young's modulus. It is a material constant, different for each substance.

What exactly is a linear elastic behavior of a material? If we apply stress to a material, strain increases proportionally. This may be true for some range of stress only – after we reach a certain value, the material may break or yield. Yielding is the increase of strain in a constant stress state.

An example of calculations

Let's assume we want to find the Young's modulus of steel. To do it, we prepared a steel rod that was pulled with a high force.

  1. We decide that the force used to pull the rod will be equal to 30 kN (30×10³ N).

  2. We determine the dimensions of the rod. Let's assume a length of 2 m (2,000 mm) and a cross-sectional area of 1 cm² (1×10⁻⁴ m²).

  3. We observed that the rod elongated by 3 mm.

  4. We calculate the strain is the rod according to the formula:

    ε = ΔL/L₁ = 3/2000 = 0.0015.

  5. We calculate the stress, using the stress formula:

    σ = F/A = 30×10³ / (1×10⁻⁴) = 300×10⁶ = 300 MPa.

  6. Finally, we divide the stress by strain to find the Young's modulus of steel:

    E = σ/ε = 300×10⁶ / 0.0015 = 200×10⁹ = 200 GPa.

Modulus of elasticity units

The units of the Young's modulus are the same as the units of pressure and stress: Pascals or newtons per square meter. In SI units,

1 Pa = 1 N / 1 m² = 1 kg·m / s² / m² = 1 kg / (m·s²)

If you are interested in mechanics, try the torque calculator as well. Or explore mohr's circle calculator to understand different types of stresses.

FAQ

What does it mean if Young's modulus is high?

The higher the modulus of elasticity, or Young's modulus, the stiffer the material. This means it can withstand a greater amount of stress.

What type of stress acts on a pillar's particular cross-section due to segment above it?

The stress on a pillar's cross-section is negative or compressive stress, due to the weight of the segment above said cross-section.

How do I estimate the stress at a particular cross-section of a pillar?

To estimate the stress at a particular cross-section of a pillar:

  1. Find the weight of the segment above it.
  2. Substitute the value of weight for force in the formula for stress, σ = F/A, where F is the force, and A is the area of the cross-section.
  3. Yay! You just found out the stress acting on the cross-section!

What is the difference between yield and ultimate tensile strength?

A solid material's yield strength is the maximum tensile stress it can handle before permanent deformation occurs. Ultimate strength is the maximum stress it can withstand before failure.

Bogna Szyk
Area (A)
ft²
Force (F)
lbf
Stress (σ)
psi
Strain calculations
Initial length (L₁)
ft
Final length (L₂)
ft
Change in length (ΔL)
ft
Strain (ε)
Young's modulus (E)
psi
Check out 35 similar materials and continuum mechanics calculators 🧱
Angle of reposeAngle of twistBend allowance… 32 more
People also viewed…

Circle skirt

Circle skirt calculator makes sewing circle skirts a breeze.

Helium balloons

Wondering how many helium balloons it would take to lift you up in the air? Try this helium balloons calculator! 🎈

Magnetic permeability

Use this magnetic permeability calculator to compute a material's permeability, relative permeability, and susceptibility.

Root mean square speed

Calculate the root mean square speed of an ideal gas.
Copyright by Omni Calculator sp. z o.o.
Privacy, Cookies & Terms of Service